Answer of your leaving message
之前都可連接,某日突然發現無法連上,重開機也不會左右轉重置鏡頭位置,戳底下的按鈕五秒以上也沒反應,重新連線也連不上線了

by 詹嘉文


您好, 謝謝來信. 先用手機的充電組(頭加線)試試, 看看是否是充電配件造成的.
如果不是, 只要藍燈有亮, 請嘗試下面的這個方法. 謝謝.
自行重寫相機內部韌體的方法及步驟 : 先不插電

Please must use this tool to format the SD card on PC ( 先用這個工具, 在PC/NB上, 格式化外接記憶卡 )/ 記憶卡一定要是健康的, 好的. 否則也會影響功能 / https://www.sdcard.org/downloads/formatter_4/index.html

Rebuild the firmware from the external SD card :
This is a manual re-build firmware procedure for your reference (recovery and cure rate is more than 90%)
Download file ( 下載軔體 到 PC/NB ) https://www.dropbox.com/s/mhl2l30tuxb0d6b/iCAM%20Pro_v421.rar?dl=0

- Uncompress/unzip it to ROOT directory of a MicroSD card [PC->SD] ( 解壓縮檔案在SD卡的”根”目錄: 一個檔案, 一個資料夾 )
- Insert the card to the camera (插卡進相機)
- Plug power cord of it. CAM will auto detect the codes in the Card (beep) to do the update ( blue light is on ) – 插上電/有讀到卡時, 會小嗶一聲
- Wait till front blue and green led is blinking. (About 2-3 minutes) – 藍綠燈閃爍, 進入待安裝模式
- Unplug power cord – 下電
- Take card out. – 卡取出
- Plug power cord again and the blue led will keep blink ( waiting for installation ) – 上電並安裝

Installation: https://www.youtube.com/watch?v=V-j_OzXsANo , If you are successful, please erase the card for normal use. (安裝步驟)

PS – this is what you see during the process ( 過程簡述 )

Insert the card with unzipped files (帶檔案並插卡)
Plug in power (上電)
Short beep ( camera detect and read the files ) in 5 seconds (嗶一聲)
After about 40 seconds (等待)
Two short beeps ( writing complete ) (2短聲嗶)
Blue and Green lights blinking – done ( wrote in ) (兩個燈閃爍 – 完成)
Unplug the power (下電)
Remove the SD and erase it ( 拔卡並刪除檔案以利後續使用 (如果以上步驟有成功) )



您好, 謝謝來信. 先用手機的充電組(頭加線)試試, 看看是否是充電配件造成的.
如果不是, 只要藍燈有亮, 請嘗試下面的這個方法. 謝謝.
自行重寫相機內部韌體的方法及步驟 : 先不插電

Please must use this tool to format the SD card on PC ( 先用這個工具, 在PC/NB上, 格式化外接記憶卡 )/ 記憶卡一定要是健康的, 好的. 否則也會影響功能 / https://www.sdcard.org/downloads/formatter_4/index.html

Rebuild the firmware from the external SD card :
This is a manual re-build firmware procedure for your reference (recovery and cure rate is more than 90%)
Download file ( 下載軔體 到 PC/NB ) https://www.dropbox.com/s/mhl2l30tuxb0d6b/iCAM%20Pro_v421.rar?dl=0

- Uncompress/unzip it to ROOT directory of a MicroSD card [PC->SD] ( 解壓縮檔案在SD卡的”根”目錄: 一個檔案, 一個資料夾 )
- Insert the card to the camera (插卡進相機)
- Plug power cord of it. CAM will auto detect the codes in the Card (beep) to do the update ( blue light is on ) – 插上電/有讀到卡時, 會小嗶一聲
- Wait till front blue and green led is blinking. (About 2-3 minutes) – 藍綠燈閃爍, 進入待安裝模式
- Unplug power cord – 下電
- Take card out. – 卡取出
- Plug power cord again and the blue led will keep blink ( waiting for installation ) – 上電並安裝

Installation: https://www.youtube.com/watch?v=V-j_OzXsANo , If you are successful, please erase the card for normal use. (安裝步驟)

PS – this is what you see during the process ( 過程簡述 )

Insert the card with unzipped files (帶檔案並插卡)
Plug in power (上電)
Short beep ( camera detect and read the files ) in 5 seconds (嗶一聲)
After about 40 seconds (等待)
Two short beeps ( writing complete ) (2短聲嗶)
Blue and Green lights blinking – done ( wrote in ) (兩個燈閃爍 – 完成)
Unplug the power (下電)
Remove the SD and erase it ( 拔卡並刪除檔案以利後續使用 (如果以上步驟有成功) )